Jymc220bi — Schematic |work| Full

Because the regulator is “all‑in‑one,” the schematic that powers a board is often just a handful of passive components around the chip. Understanding that schematic is the key to troubleshooting, customizing, and confidently integrating the module into any design. Below is a functional block diagram that abstracts the internal architecture (no copyrighted layout, only a conceptual view).

| Feature | Benefit | |--------|----------| | 4.5 V – 38 V | Works with a wide variety of battery packs and wall‑adapter voltages. | | Fixed output: 5 V (1 A) or 12 V (0.5 A) depending on the variant | No external feedback network needed for the most common voltages. | | Integrated MOSFET + inductor | Minimal external parts → tiny PCB footprint (≈ 15 mm × 10 mm). | | Built‑in protection: over‑current, over‑temperature, under‑voltage lockout (UVLO) | Safer for both the module and the load. | | Low cost & high availability | Ideal for budget‑sensitive projects. | jymc220bi schematic full

| Parameter | Value (typ.) | Unit | |-----------|--------------|------| | Output Voltage (VOUT) | 5.0 | V | | Output Current (IOUT) | 1.0 | A | | Switching Frequency | 250 | kHz | | Efficiency (typ.) | 85–90 | % | | UVLO Threshold | 4.0 (low) / 4.5 (high) | V | | Over‑Current Protection | 1.2 × IOUT (trip) | A | | Operating Temperature | –40 ~ +85 | °C | | Feature | Benefit | |--------|----------| | 4

(If you are looking for the official datasheet, you can download it from the manufacturer’s website or reputable component‑library sites – the link is provided at the end of this article.) 1. Why the JYMC‑220BI Matters The JYMC‑220BI is a compact, integrated step‑down (buck) switching regulator that has become a staple in low‑cost power‑supply designs for hobbyists, DIY‑electronics, and even some commercial products. Its appeal comes from: Usually left unconnected

| Ref | Part | Value / Description | Notes | |-----|------|---------------------|-------| | | – | 4.5 V – 38 V | Connect to the raw supply. | | C1 | 100 µF electrolytic (X5R) | Input bulk capacitor | Placed as close as possible to the IC pins. | | L1 | 22 µH (ferrite core) | Integrated in‑package inductor (part of the chip) | Not a discrete part – drawn for illustration. | | D1 | SS34 (Schottky, 3 A, 40 V) | Free‑wheel diode | Must be placed with the cathode toward VOUT. | | C2 | 22 µF, 25 V X5R | Output bulk capacitor | Works together with the internal capacitor to meet ripple specs. | | C3 | 0.1 µF ceramic, 50 V | High‑frequency decoupling | Located right at the IC power pins. | | RFB | – | Internal (fixed) | In the 5 V version the feedback divider is inside the IC; for the adjustable version, replace with a resistor divider (R1, R2). | | IC | JYMC‑220BI | 5 V, 1 A buck regulator | Pin‑out described in section 4. | | GND | – | Ground plane | Keep the return path wide and low‑inductance. |

Vin ---- C1 ----+----+--------------------+----> VOUT | | | | IC1 D1 | (JYMC‑220BI) | | |--- SW (pin 3) ----+---|<---+ | | | | | L1 (integrated) | | | | | | +----+--- GND ---------+----------+ | | C3 C2 | | GND GND In a real PCB you will see a thermal pad on the bottom of the IC that should be soldered to a copper area (often connected to ground) to aid heat dissipation. 4. Pin‑out & Electrical Characteristics | Pin | Name | Description | Typical Voltage | |-----|------|-------------|-----------------| | 1 | VIN | Input voltage (4.5 – 38 V) | – | | 2 | GND | Ground (common) | 0 V | | 3 | SW | Switching node (connects to the internal MOSFET) | Pulses between VIN and GND | | 4 | FB | Feedback (fixed internally for 5 V/12 V; external for adjustable) | ≈ 0.6 V (reference) | | 5 | EN | Enable pin (active‑high). Pull high to turn on; pull low to shut down. | 0 V or 3.3 V | | 6 | SS | Soft‑start control (optional). Usually left unconnected; pulling low reduces inrush current. | – | | 7 | TEMP | Internal temperature sensor (not usually accessed). | – |